Jump to content
IBIFTKH

For sale - Wild Willy 2, another Willy driver figure & more

Recommended Posts

Having a little clear out -

Kamtec lexan Bowler Wild cat shell. It was previously fitted to a CR-01 using FJ40 body mounts. It has a few light scratches but no splits. £15 inc UK post.

DSCF3531_zps5dd720b1.jpg

Tamiya Toyota FJ pick up complete body set (from GF-01 kit). Sold.

Single Buggy Champ rear wheel & tyre. Used but very good condition. £6.00 inc UK post.

DSCF3332_zps7299151d.jpg

SRB Bloke stinger exhaust. Paint scratched around mounting point. £20.00 inc UK post.

DSCF3287_zps50205634.jpg

Painted Wild Willy torso figure. New built. Sold.

DSCF3527_zps33862a5b.jpg

Payment by Paypal gift or you pay fees please.

Any questions, please ask.

Cheers,

Rob

Share this post


Link to post

How many turns can the TBLE-02 take?

edit: nevermind, just looked it up. It cannot take my Tamiya Transpeed MS motor. Is there a Tamiya ESC that can?

Share this post


Link to post

Tamiya USA site says silver can or Sport Tuned, 25 turns or higher. It's supplied with a Torque Tuned motor in the GF-01 kit so obviously it's fine with that too.

For brushless they say 10.5T or higher, sensored only.

Hope this helps,

Rob

Share this post


Link to post

There's no easy way to say this so I'm just going to go for it,

Can I have the Willy please?

  • Like 1

Share this post


Link to post

The Bowler Wildcat body, SRB exhaust and SRB spare wheel from the previous post are still available.

I also have this Wild Willy M38 body for sale. I originally bought it for a project which went in a different direction so now it's spare.The old paint was stripped off, then it was re-assembled and re-painted.

It's a mixture of old and new parts. Most of the body parts are original as far as I know - shell, windshield & brackets, roll bar, spare wheel and fuel can. I replaced one of the front inner wings and the tailgate because they were damaged. The front grill is an aftermarket part, plastic and much chunkier than the original. The grill mounting tabs (underside of the bonnet) were broken and had to be removed to fit the grill. Wild Willy himself, the steering wheel & column, the winch and spotlight covers are all new parts. The roll bar is scuffed in places and there is a small crack by one of the small tailgate screws.


DSCF3685_zps08e403f6.jpg

DSCF3684_zps7704aa96.jpg


Sold.

Cheers,

Rob

Share this post


Link to post

Bump and price drop.

Bowler body £15 posted

SRB exhaust £20 posted

SRB wheel & tyre £6 posted

Also selling these -

4 x Fastrax 90mm tyres on 1.9 'scale' wheels. They've been fitted to a chassis but never run. Sold.

Sand Scorcher headlight lenses, light buckets etc. Light buckets have been drilled for LED fitting. Sold.

Any questions, please ask,

Cheers,

Rob

Share this post


Link to post

The Kamtec Bowler is still available, as are the SRB stinger and spare.

And another Wild Willy body, this time a WW2. It's mainly new parts except the spare wheel and roll cage. The grille is a plastic aftermarket part, chunkier than the standard WW2 grille and of course has the 'correct' vertical slats. I've put a fair bit of time and effort into it so hopefully someone will be able to give it a good home :-)

DSCF3769_zps7a88da36.jpg

DSCF3773_zps11c2ae79.jpg

DSCF3774_zpsaf129ed5.jpg

DSCF3775_zps6397d6dc.jpg

DSCF3777_zps9fc908f9.jpg

driver detail
DSCF3767_zps5c7c9cf9.jpg
Sold

Any questions, please ask.

Cheers,
Rob

Share this post


Link to post

A couple of figures -

Mr Red (sold)
DSCF3794_zpsfa6e9189.jpg

Mr Blue (sale agreed)
DSCF3801_zpsd57575b5.jpg

I'm asking £11 each plus £3.90 UK post, paypal gift or you cover the fees please.

Any questions, please ask.

Cheers,

Rob

Share this post


Link to post

Cheers Rob - looking forwards to Smurf Willy popping through the postbox .

Share this post


Link to post

@The Smoothee, thank you, though that's not a compliment you hear every day!

Arron, Mr Blue is on his way, hope you're happy with him.

cheers,

Rob

  • Like 1

Share this post


Link to post

@The Smoothee, thank you, though that's not a compliment you hear every day!

Arron, Mr Blue is on his way, hope you're happy with him.

cheers,

Rob

Just hope he likes his new ride Rob lol

Share this post


Link to post

And another one! Meet Hazard Willy :)
His arms are just tacked on for the photos, not glued (makes it a lot easier to fit him, otherwise you have to disassemble half the bodyshell!)

DSCF3802_zps024aee71.jpg

Sold

Cheers,
Rob

  • Like 1

Share this post


Link to post

Here's his little brother :)

DSCF3807_zps5ad5dbe1.jpg

Sold

Any questions, please ask.

Cheers,
Rob

Share this post


Link to post

These are great. Any chance of a how to thread? If I can 50% as good as these I would be over the moon

Share this post


Link to post

I could, but it probably wouldn't be as good as Fabrizio's guide here - http://www.tamiyaclub.com/willy.asp

I usually spray the helmet first, then work on the face, but that's just personal preference (a blob a blu-tack is great for masking the face!). I'm not sure what brand of paint Fabrizio uses, mine are Games Workshop.

If you want a list of colours or if there's any other way I can help, just give me a shout.

Share this post


Link to post

I could, but it probably wouldn't be as good as Fabrizio's guide here - http://www.tamiyaclub.com/willy.asp

I usually spray the helmet first, then work on the face, but that's just personal preference (a blob a blu-tack is great for masking the face!). I'm not sure what brand of paint Fabrizio uses, mine are Games Workshop.

If you want a list of colours or if there's any other way I can help, just give me a shout.

Great, I will have a read later. It was more how to use a gun (settings, pressures) and water down the paint etc I was interested in. It is a skill it would like to learn but I have not idea of a starting point.

Share this post


Link to post
×
×
  • Create New...