XV Pilot 1936 Posted February 24, 2015 Might I suggest the GPM ballraced alloy steering rack upgrade? I use it on my DF01 and FF01, and it is a direct fit, far smoother and less sloppy than the stock plastic, and not likely to snap either. Share this post Link to post
bigoggy 203 Posted February 24, 2015 I have 5 of those, but just checked, and every single one has a crack, to some degree. I would suggest following the above advice. Share this post Link to post
Pingman 4 Posted February 24, 2015 where do I buy it from? I would probably be happy with one with just a crack, mine snapped where the ball screws in so is totally useless Share this post Link to post
Nobbi1977 1793 Posted February 24, 2015 where do I buy it from? I am guessing http://www.fusionhobbies.com/product/df1048-gpm-df-01-alloy-steering-assembly Probably cheaper than Tamiya plastic too Share this post Link to post
XV Pilot 1936 Posted February 24, 2015 That is the one! Asiatees also have them. Share this post Link to post
bigoggy 203 Posted February 24, 2015 where do I buy it from? I would probably be happy with one with just a crack, mine snapped where the ball screws in so is totally useless They all go in the same place, and I would be unwilling to even give these away, such is the damage. Share this post Link to post
Pingman 4 Posted February 25, 2015 **** £15.49 inc del more than i'm wanting to spend on a car worth £40 tops lol Share this post Link to post
skip665 169 Posted February 25, 2015 I bought a TA-02 with that part broken in half and the cheapest place was Jasons store in Japan for the sprue - think it was about £6-7 delivered... Share this post Link to post
Pingman 4 Posted February 25, 2015 I bought a TA-02 with that part broken in half and the cheapest place was Jasons store in Japan for the sprue - think it was about £6-7 delivered... Just checked and they don't have one, don't need anything else from the spur either Share this post Link to post
z00ter 392 Posted February 25, 2015 I should have one I will check on the weekend if you haven't got one by then. Share this post Link to post
chickenman242tk 266 Posted February 26, 2015 i have a complete sprue and access to more if needed ,pm me if you come unstuck. Share this post Link to post
Pingman 4 Posted February 26, 2015 that's great, Z00ter is checking if he has one for me, if not will message you thank you Share this post Link to post
Pingman 4 Posted March 4, 2015 hey bud its this u are after ? That one looks a little different, guess it's from a different model? Share this post Link to post
z00ter 392 Posted March 4, 2015 Im prity sure this is out of a TA01 (it was in the box with the shok towers etc when I upgraded my TA01 to a TA02 with gpm parts. so 99.99% sure its ta01 (although I do have another but will take some a bit to find it as its buried) if the one above wont do the trick for you (I can take a better pic if needed) Share this post Link to post
Pingman 4 Posted March 4, 2015 it looks different, mine doesn't have that notch cut out, guess it might fit Share this post Link to post
z00ter 392 Posted March 4, 2015 Iv gota dig some other stuff out in a hour or so, so will have a look for the original TA02 one which I had replaced with gpm. will update in a bit Share this post Link to post
z00ter 392 Posted March 4, 2015 Hey mate, couldnt find the other one, i thinks its burried ... but i did find one on the sprue from my Tasan TA02 to ompare, and it is exactly the same so if its good, pm me ur address and ill try post it out by end of week. Share this post Link to post