hayabusa95
-
Posts
28 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Posts posted by hayabusa95
-
-
Just a little update
Part numbers SCX2-6063-6BK (Stock hex adaptors fall off easly, and pins!)
106032P (Looking for more power in budget)
Without modification on gear cover it is the biggest pinion you could use.
I havent found Hot Racing 20mm wheel hub extensions on a website which ships here.
-
Sorry about delayed reply.
Maybe, you have already read what you're gonna read below...
Called "Sturmkind" handmade, app controlled RC drift cars from Germany. Some options: RWD-FWD-AWD, DRY-WET-DIRTY-SNOW which changes driving characteristic.
Actually it looks like drifting, 360 degree turnable tires on the middle of car.
Today checked their website again, saw much development.
There are different spec of cars, for new customers discount coupon available, please check their website
To me, they are little pricey. Havent tried but love them a lot.
-
On 2/5/2022 at 1:44 PM, whahooo said:
I would love to try internal spring shocks
So do I, they look much better, 2 on per wheel
3 on per with supersoft spring might work
-
3 hours ago, 87lc2 said:
How did you resist jumping over that barrier on the right? Would have been the first thing I did
Truck rarely jumped during run. I'll take another video footage for you
2 hours ago, Nobbi1977 said:I have never thought of snow on the ground in Turkey. I associate it will 35 degree sun.
Not everywhere. West side of Turkiye is warmer than east.
-
Today 2°C , punch and top speed was better at first, temperature effect on battery I guess.
I have never seen wheel threads on other cars, very interesting.
Hope you enjoy the footage 💨
-
1
-
1
-
-
@GeeWings 👏👏
@Nikko85 Unfortunately, you may see ownerless dogs and cats in my country. I live in capital people building shelters for dog herds. Uncontrolled birth of cats, havent seen them around in europe as far as what I seen on TV.
Salvador- intern, we saw him about 6 years ago in a box a girl carrying. He has broken rear leg dont remember left/right, had surgery, healed.
-
2
-
-
End of sponsor plate. I like to share sticker sheet photoshop file, not sure its allowed to share on forum, or possible.
3 spacers behind top screws***
-
5
-
1
-
-
Smaler, no air bubbles. Try a lot but its too hard to do without bent. Added one more spacer behind top screws. Working on stickers...
Setted -20 timing that gives more punch torque, much better but still just a little wheelie on carpet.
-
3
-
-
-
Custom sponsor plate build
Used acetate sheet, middle and bottom screws are longer m3x25mm with plastic spacer, from kit leftovers. Mat black vinyl wrap.
Im not sure about cutting half and using middle, bottom screws to hold. Work in progress.
-
1
-
-
They are 110mm. Working on truck for custom sponsor plate, after rebuild i can contact you for sag and travel. The sag quite similar on rear like yours, on front almost no sag.
After first ride, i felt in love M/Ts .
48 minutes ago, whahooo said:I´m a fan of long travel Shocks and a soft Setting, so you get some negatibe travel and a bit of Sag.
So am I.
26 minutes ago, 87lc2 said:as low as possible and the links parallel to the ground
They are not. I have measure for 100mm shocks, there are no place for full travel, might hit on esc/receiver plate. Attached belove. Im gonna try to lift that part.
Draw that on paint for better explanation. You know 3d designer on forum?
44 minutes ago, 87lc2 said:If the truck is stable with the current wheelbase no need to change it. Longer wheelbase = more stability but less turning radius, shorter wheelbase = less stability but better turning radius.
Finding sweet spot
-
I have MST MTX-1 after glueing tires it wheelies a little indoor, no wheelies on snow
Just thinking about some upgrades shocks, alu pivot balls, wheel/tire set (w/foam insert), wb extension...
After reading replies decided to start from tires.
-How to measure/set/decide link and shaft lenght? (stock wb about 11in, 12.5in or less/more for better landings?)
-I like 2.6 wheels look, but not sure car can handles or not.
-Stock shock travels very limited(110m length). 100mm should be better, internal shocks ??
May I get your ideas please?
Barış
-
Tire glueing day with my intern, Salvador.
I was using plastic tip for glue bottle, Gravity RC metal tip glue bottle, i can recommend. 👍
-
6
-
-
Front and rear same increasement, also for each links upper lower?
There are aluminum, steel and brass pivot balls on amainhobbies, only +1 usd for brass.
On 15t brushed, stock setup no wheelie. Replacing 24t to 17t pinion maybe helps. (MST MTX-1)
Good luck,
Barış
-
Snow Runner ❄❄
Stucked 2-3 times, but its was fun looking him whole run. People metioned '' Watch out TOYOTA, dont bump into that!! ''
After run, visual check OK. Used green slime on shocks, its sticky and very hard to clean, so shocks might be good.
Im worried about other parts maybe water leaked in, not sure where to check.
How often re-oil bearings, how? WD-40, drying then oil, enough?
-
3
-
-
-
5
-
-
Attached Toyota sticker design, if you wanna use. ❤️
-
4
-
-
-
Truck looks perfect, what mods does it have on? Hex extension vs offset wheel adapter, same stress on drive train?
-
1
-
-
Hello,
Since 2015, im following some topics on this forum which shares Tamiyas' only before. Maybe Im wrong b/c following 'The Builds' section. Im glad you are sharing other brands.
Its my first topic which looks like a topic, let me introduce myself. Im Barış, from Türkiye. There are a little communities here, R/Cs very expensive including second hand. I like this forum cause members are very kind and they are trying hard on their builds. (And I love TAMIYAs)
I had some rtr vehicles, kits and a scratch build. Now, returned this hobby, I dunno why
The plan was sharing the 1st topic about that kit. Im following their topic for benefit 
Thank you @Mad Ax @joeling
Ordered MST MTX-1 month ago and the other parts, still waiting for servo, transmitter.... (b/c of covid transporting is very slow) also contacted amainhobbies about shock oil issue where i ordered the kit, they sent a bottle of 10wt.
Electronics 3-pole reedy 16t brushed w/1060 esc on 2S. Powerhd waterproof 23kg digital servo.
Now, waiting for shock oil and focusing paint. Its harder than before, planned bad paint schema. Which is darker, which paint should I start with... confused. Im sure i can handle it.
Here are some colors which im gonna use on this body. New can about 124-132 grams. (PS-1, 55)
PS-59 104gr. , '15' 90gr. , '41' 75gr. PS-41 feels like there are 1/4 maybe less paint in it. What is the empty can weight?
-
3
-
-
They look perfect, Im happy to see more MTX-1 on forum.
Also working on mine
Could you share running video that would be very fun to drive w/ your daughters, have fun.
-
I have never try that but using rock salt for making rust, using copper, black than use both greens and yellow for same color effect.
-
Here is mine!!
15t reedy 3pole 540 /quicrun 1060
To me some screw holes confusing, its my 3rd kit after Blitz ESE and Associated T5.
Barış ☮️
-
1
-
-
Hello everyone,
I was searching on web for budget rally build and found M03R.
What do you think about converting to Rally?
What parts need?
Im not sure to start that project and just wanna ask you
Have a great day.
Brushed motors for a Clodbuster
in Monster Trucks, 4x4, Wheelie Rigs and Crawlers
Posted
Running 15t version both 0 and -20 timing on 2s , no problem at all. (MST MTX-1 4WD) Changed pinion 24 to 32, gonna run it soon. If something happens ill warn you