Jump to content

Mark3gti

Members
  • Content Count

    164
  • Joined

  • Last visited

Everything posted by Mark3gti

  1. Post 40th blues weekend bump.. May trade, what you got? ideally trf Tb evo items of interest.
  2. Interesting, what else is in the collection? apologies I donโ€™t need a m03 at the Moment btw.. ๐Ÿ˜ข
  3. Looking for a few items for my trf415 build. first up is a floating servo mount, can be off any trf / ta07 etc as going to be retrofitted. let me know if one lying around.. mark
  4. planning a steering conversion, basically the msxxmr layout so much lower profile like the 419. but will require a servo relocation,:so easiest way I can see is to fit a floating servo holder, couple of holes in the plate and its relocated easily. Now to find one, went through the manuals and 417v5 onwards have them. snyone got a spare on they donโ€™t want? ๐Ÿ˜ฌ but opening a can of worms, have the arms and bridge secured, possibly posts as well, which Iโ€™ll trim right down and make a small brace like the 419. will have to redrill the chsssis as the holes need to be further back than they are now. guess there is only so much you can do on the orig so plate With upgrading Kits before you Have to splash out on the up to date plate. But I am going to try. ๐Ÿ‘ this is my outdoor car but also my โ€˜tinkering carโ€™ so will keep trying to do what I feel I can for now..
  5. Just resting with younger brother! ๐Ÿ˜‚
  6. to avoid major issues Iโ€™m going to run a 3000mah shortie, as fits nicely where the bulkhead permits. will have to add some weight thou to get close to the target weight. 1350g I think from memory..
  7. electrics back in, need to sort the servo leads, caps and aerials then hopefully can be run again..
  8. test fitted these I found in the box from when I bough the car, nice ally lay shaft bearing holders. found that I need a different top plate cos they donโ€™t sit flush like the plastic ones. so hoping to acquire a couple of the lay shaft covers off a msxxmr I think it is. then I will have the ability to shim the msxxmr lay shaft to stop the front belt catching slightly at spur side.
  9. Yeah thanks! ๐Ÿ‘ has seen it, postage is a bit of a killer thou.. plus Iโ€™ll prob get hit import on it as well! ๐Ÿ˜ญ thanks thou! ๐Ÿ‘๐Ÿ‘
  10. On the look out for a steering bridge off title chassis. any around? thanks in advance uk based..
  11. Thatโ€™s good! it Was tough to picture but they are 1997 Impreza wheels.. hopefully the right ones! ๐Ÿ‘ They are brand new unused but not packaged. make me a offer ๐Ÿ‘
  12. Are these the right rims? Iโ€™ll check the code later tonight..
  13. Weekend bump ๐Ÿ˜ May also consider trf / Tb Evo related trades.. money preferred but try me ๐Ÿ‘
  14. I do indeed thanks! ๐Ÿ‘ yeah I can do this one for 125 posted.. its almost complete, a few bits to finish off and be good to go! ๐Ÿ‘๐Ÿ‘
  15. all the way from a friend in Hong Kong, rc cox X-ray 0 degree hub carriers which can be used to form rear ars. Had planned on fitting to my indoor racer but ars is better suited outdoor so at some point Iโ€™ll configure and fit to this.. just a bit of minor trimming and theyโ€™ll fit perfectly..
  16. Almost finished front roll bar, setup station and electrics and be almost complete.
  17. Last nights work.. bit boring but got them fitted.. also managed to do a lot more! ๐Ÿ‘ but I was so in the groove I didnโ€™t take any other pictures till the end.. ๐Ÿ˜ฑ๐Ÿคฃ
  18. looking good I think.. ran out of time tonight, but hopefully this week in the evenings around childcare and what not Iโ€™ll get it mostly finished up. ๐Ÿคž๐Ÿ‘
  19. had some spec r drive shafts in my evo 5 a while back, and kept hold of the pins as they have a flat on them, so you can get a good grip on them with the grub screw. also treating it to new aluminium rear wheel spindles, but only on the rear, Iโ€™m sure Iโ€™ll bend them up front! ๐Ÿ˜ฃ
  20. rare and hard to find, was lucky they were in the box of a car I bought! ๐Ÿ˜ฒ think itโ€™s more an issue that they bend with big impacts, guess not crashing would sort it! ๐Ÿ˜ฌ
  21. Haha oh yeah forgot about that one! ๐Ÿ˜ฒ๐Ÿ˜ฑ๐Ÿ˜ณ
  22. Also have a spares car ( perhaps 95% complete, it is a roller Just need roll bars And perhaps a tensioner but not essential ) that I plan to Advertise shortly for 125 posted in UK but could do a deal on both. and a correct rare spool I could include for the right deal. ๐Ÿ‘
×
×
  • Create New...