LA.19
-
Posts
28 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Posts posted by LA.19
-
-
2 hours ago, TurnipJF said:
Is it working though?
I found out by a youtuber that said its normal if its blinking because it means ur not in turbo mode or boost mode unless if you use those modes then ur esc wont blink again so lmaoooo manual didnt tell me nun bout that soo ill info when it get to run and show jts top speed hehe thank you for ur support
-
1
-
1
-
-
I did and i got it calibrated, and are able to be programmed by program card butttt its still blinking blue😁😅
-
So i was calibrating my rocket rc 120a esc and in the middle of the calibration i did something wrong and now when i want to recalibrate it i cant, the manual says when calibrating press the on/off button to continue thr next step but now when i do so the rc just shut off when i press the on off button so whenever i turn on the esc it blinks blue when it wants calibrating it does that but when i press the on off button to continue to it judt shuts off so now i need to find out how to reset my esc its a rocket rc 120a esc
-
On 3/22/2024 at 10:01 PM, alvinlwh said:
48p
Ver 1 goes from 65T - 96T
Ver 2 goes from 62T - 90T
64p
Ver 1 goes from 74T - 130T
Ver 2 goes from 87T - 118T
I usually go for Ver 1 as it is cheaper.
But ver2 also fits right?
-
-
So i have a surpass hobby brushless kk 3650 size motor
So the motor is 6900kv and the esc is 60amps
I bough the combo but im worried if my 60 amps esc can handle a 3650 size 6900kv brushless motor
please Helpp me
-
Yo its sold out noooo
-
14 hours ago, alvinlwh said:
48p
Ver 1 goes from 65T - 96T
Ver 2 goes from 62T - 90T
64p
Ver 1 goes from 74T - 130T
Ver 2 goes from 87T - 118T
I usually go for Ver 1 as it is cheaper.
But both version do fit right?
-
Alr thank you so much
-
10 minutes ago, Honza said:
Check the article I linked earlier. Without modifications, you can fit 35T/48p or 48T/64p. For larger pinions, you'd need to file part of the chassis.
Alr thank you so much, btw there's 2 version of the spur which one should i get?Or they're the same?
-
On 3/20/2024 at 7:30 PM, alvinlwh said:
3Racing will post anywhere in the world and HK to ID will not cost a lot.
https://3racing.shop/collections/gear/gear
However, their smalles spur is 65T and I had never seen a 48p spur smaller than 60T. However a 65T spur with a 46T pinion will get you very close to the ratio you are looking for.
Alternative source for your part of the world will be Lazada or TB.
Btw what version of the spur should i get to fit with my tamiya tt02 high speed gear adapter theres 2 kinds i see
-
On 3/20/2024 at 7:30 PM, alvinlwh said:
3Racing will post anywhere in the world and HK to ID will not cost a lot.
https://3racing.shop/collections/gear/gear
However, their smalles spur is 65T and I had never seen a 48p spur smaller than 60T. However a 65T spur with a 46T pinion will get you very close to the ratio you are looking for.
Alternative source for your part of the world will be Lazada or TB.
So 3 racing is cheaper to id then rw?
-
On 3/20/2024 at 11:18 PM, Pylon80 said:
One does not need to use the YR adjustable mount necessarily. You can use an online gear calculator to find a combination of spur and pinion in 48p or in 64p that will fall onto the same motor mount holes as the original 0.6M part it replaces:
https://evolventdesign.com/pages/center-distance-calc
For example, if you want to use the holes 'A' or '16' of the mount, you are replacing the equivalent of 70t spur and 16t pinion in 0.6M. Distance is 25.80mm. Final Drive Ratio is 11.4 which is very slow!
In 64p (or 1/64in module), you could use 94t spur and 36t pinion which comes out to the exact same distance of 25.80mm, and a much lower (faster) FDR of 6.8.
You could do the same calculation with the other holes of the mount and get much lower FDR's (much faster). All of this without spending a dime on a different mount nor having to adjust the gear mesh.
I do have the yr mount alredy tho
-
On 3/20/2024 at 7:30 PM, alvinlwh said:
3Racing will post anywhere in the world and HK to ID will not cost a lot.
https://3racing.shop/collections/gear/gear
However, their smalles spur is 65T and I had never seen a 48p spur smaller than 60T. However a 65T spur with a 46T pinion will get you very close to the ratio you are looking for.
Alternative source for your part of the world will be Lazada or TB.
U sure this tt02 can handle 46tooth pinion
-
On 3/20/2024 at 7:30 PM, alvinlwh said:
3Racing will post anywhere in the world and HK to ID will not cost a lot.
https://3racing.shop/collections/gear/gear
However, their smalles spur is 65T and I had never seen a 48p spur smaller than 60T. However a 65T spur with a 46T pinion will get you very close to the ratio you are looking for.
Alternative source for your part of the world will be Lazada or TB.
Alr i seee thank you ill take consider
-
**** ur a life saviour ty so muchh
-
1
-
-
4 minutes ago, ThunderDragonCy said:
It means how the teeth of the gear fit together.
48dp is bigger teeth than 64dp. They do not work together.
I have tried looking on amazon but i can't find anything. Can you find a hobby store that sells touring cars?
I can but im not sure if they sells tho i might need to check em
-
So if it mesh it means good?
-
Also whats the differnce between 48dp and 68?
-
20 minutes ago, ThunderDragonCy said:
Amazon doesn't have anything decent. For smaller than stock gears you need to switch from the tamiya metric 0.6mod pitch gear teeth to 48dp imperial size. So long as both pinion and spur are 48dl they will mesh.
What country are you in? If uk, go to RW Racing.
Spurs : https://rwracing.co.uk/shop/ols/products/rw-standard-touring-car-spurs
pinion
https://rwracing.co.uk/shop/ols/products/cnc-steel-pinions-324864dp
What does mesh means? 😁😅
-
20 minutes ago, ThunderDragonCy said:
Amazon doesn't have anything decent. For smaller than stock gears you need to switch from the tamiya metric 0.6mod pitch gear teeth to 48dp imperial size. So long as both pinion and spur are 48dl they will mesh.
What country are you in? If uk, go to RW Racing.
Spurs : https://rwracing.co.uk/shop/ols/products/rw-standard-touring-car-spurs
pinion
https://rwracing.co.uk/shop/ols/products/cnc-steel-pinions-324864dp
I live in Indonesia😭💀
-
11 minutes ago, Honza said:
That also requires adjustable motor mount to set-up proper mesh
Although 48p can work with the original mount, the adjustable mount provides more options and precision.
Yup i also had this
-
Help me plss im looking for a spur gear and pinion gear for my tt02 if can 34+ pinion gear and 50 lower spur gear. Im looking for high speed gears. If can please give me amazon links. Also i have a high speed adapter from tamiya already soo please helppppppp
-
Servo Saver or Servo Horn
in Build Tips and Techniques
Posted
My servo saver on tt02 was clicking because i didnt know how saver works and my epa was too much and when i turn the saver opposite dorevtions its kinda loose and ticks so i just put a slice of tape on the end of the metal rings and just closed it and it stopped clicking and no more loose soxo yeah idk how long it would last tbh😂