Search the Community
Showing results for tags 'impreza'.
Found 6 results
-
Hi all, I've got a hpi subaru impreza 98 wrc bodyshell, I purchased it without the decals and now I'm trying to find a set, I tried/ had a set of tamiya scooby decals but they were slightly smaller then needed and didn't look decent enough for my liking, does anyone at all know where I could try to find some, or even a scanned copy of the original decals possibly?? I contacted hpi themselves but they can't help me out Thanks
-
Welcome to my build thread. After starting a introduction topic someone mentioned i should make one, so here it is. Basically i'm going to try and convert the Tamiya Impreza WRC body into the road going Impreza called the P1, which i happen to own. The Kit: Tamiya 58210 This has been stored in my attic for the last 16 years. What i am trying to make: Subaru Impreza P1 What is the Impreza Prodrive P1? Its a limited edition version of the Japanese spec Impreza STi type R Coupe only ever available in the UK. Limited to 1000 units, built in 1999 by Subaru UK in collaboration with Subaru Japan, STi, and of course Prodrive. For those of you that dont know who Prodrive are, they made all the WRC Imprezas. The biggest difference between the Tamiya shell and the P1 is obviously the fact that Tamiya based it on the WRC car, which means i need to convert it a little. The roof air vents need to go as do the bonnet vents. The front bumper is incorrect , the P1´s front splitter is missing, the rear wing from the P1 is totally different (made by McLaren) and last but not least the wheels are incorrect. The Tamiya body i also too wide and would make up a perfect 22B version of the car, but honestly i'm not sure what to do there. I have looked all over the internet but i cannot find any different versions of the classic styled Impreza other than the WRC cars . I will be trying to make up all the P1 relevant decals myself using coral draw. I have never done that before, but im sure youtube can help . That will consist of: Prodrive P1 Titanium badges Front Splitter with drivers lights and covers (Not fogs!) SUBARU Lettering on the boot O.Z Racing lettering for the wheels Wipers front and rear P1 embossing on the rear spoiler Carbon gurney flap on the rear spoiler Custom number plates as in the picture from my P1 I am not going to cut up the original body or rear spoiler, i would rather leave those completely untouched so i have ordered the following at Siedel´s. Tamiya 05726 Mirrors Lexus GS400, these look like the impreza door mirrors that are missing from the kit. Tamiya 04134 Spoiler Impreza WRC 1999 Tamiya 1825324 Body Impreza WRC 1999. Tamiya 0445837 Wheels Impreza WRC 2001. These are exact copies of the O.Z Racing wheels used on the P1, just in the wrong colour. Tamiya 50419 Tyres 26mm, these are the same as the original kit ones and copies of the Pirelli P Zeros. Which the P1 originally had. Tamiya 53113 Inner Sponge The TA03F Chassis plus Hop-Up Options. I have finished building the chassis and used the following Hop-Ups. 53280 TA03 Super Low Friction Damper Set 53263 Dyna-Run Super Touring Motor 53279 TA03 Torque Splitter (front mounted) 53309 TA03 Titanium Suspension Shaft Set 53287 TA03 Carbon Reinforcing Plate 53275 TA03 Alu Motor Heat Sink 53268 TA03 Urethane Bumper Set 53113 Racing Inner Sponge Set. TA03 Race Ball Bearing set (Carson) Now time for some pictures, the chassis so far: The O.Z racing wheels arrived today, just need to paint them the correct colour. That would be anthrazit, a colour thats not available from Tamiya so i will be using TS-38 Gun Metal Grey. Thats all for today, thanks for reading. Im off back to the UK tonight so nothing will be happening for the next 14 days.
-
Hello all, I'm looking for finished versions of the 1/10 bodies from Tamiya of either the 2007 or 2004 WRX Impreza WRC Rally cars driven by Solberg. Must be in new condition, preferably sealed. Please get in touch if you know where I can find either. Willing to pay good $. Thanks very much Julez
- 1 reply
-
- subaru
- monte carlo
- (and 6 more)
-
Hi, I have a Tamiya Subaru Impreza No.58226 1/10 McRae 1998 Edition with TL-01 chassis up for sale on Ebay. The kit is unbuilt with all parts still in the original packaging. Just a bit of wear on the box from storage. Looking for it to go to a good home. See listing and pics for more details: https://www.ebay.co.uk/itm/Tamiya-Subaru-Impreza-No-58226-1-10-McRae-1998-Edition-New-NIB/222902278929?hash=item33e602db11:g:VKcAAOSwEHhau~gv
-
Here for sale is my TB-01 chassis in execellent condition with a Tamiya QD 2007 Impreza body in excellent condition also with full tamiya light units and control unit. TB-01 chassis - new build. Alturn USA 775 Servo - New TBLE02 ESC - New Torque Tuned Motor - New Real alloy wheels - New Rally block tyes - new Flysky Rx - used but new condition. Couple of minor marks on the bottom of the chassis but nothing serious. Diffs and drive train are smooth. Its spent its life on the shelf. Comes with spare Gold Tamiya Wheels. BNIP tamiya impreza decals. £110 posted to your door. Will ship international for extra cost. lots more pics on request. 07543967949 if any questions.
-
As per post title after a new H parts tree from the subaru impreza 1997 bodyparts set. If anybody has one spare or can help me find one that would be great!