Jump to content
rc-martin

Sand Rover SRB

Recommended Posts

Thought I'd start a new build thread for my latest project. 

I've entered in the 2022 Iconic RC revival with my trusty Sand Scorcher but thought I'd try something different body wise this year.

I'd seen a few people mount Sand Rover bodies to SRB chassis in the past but wanted to go a little further and add a couple of figures with some animatronic actions also.

New, reproduction Sand Rover shell was acquired and got stuck straight in with chopping out the original interior panel with the dremel tool.

20220321_134412_copy_1049x590.jpg

20220321_152228_copy_1096x617.jpg

20220321_181808_copy_662x1177.jpg

20220321_184221_copy_1030x580.jpg

  • Like 4

Share this post


Link to post
Share on other sites

I was going to use an old Sand Rover chassis tub under the body, attached to the SRB chassis like a few other people have done but after watch a few of Danny Huyhn Creation videos I thought I'd have a go at custom making a tub from 2mm black styrene.

Made a cardboard template first of the base and then just built up from there

20220322_165626_copy_992x558.jpg

20220322_165643_copy_978x550.jpg

20220322_200933_copy_975x549.jpg

20220322_202957_copy_1040x585.jpg

  • Like 2

Share this post


Link to post
Share on other sites

I spent ages searching for suitable figures that where sufficiently articulated, the right scale and looked like they would belong in a beach buggy.

Finally decided 7 1/2 inch action figures where approximately 1/10 scale and that WWE wrestling figures where going to be the best option, just need ones now that would look good in a beach buggy. Decided on a Undertaker figure and Trish Stratus as the passenger.

The Undertaker arrived first and I didn't hesitate at getting stuck into him :lol:

Sub micro servo added into his body for his head movement and freed off his shoulder and hip joints for looser movement 

Screenshot_20220413-054426_eBay_copy_800x1139.jpg

Screenshot_20220413-054518_eBay_copy_792x1290.jpg

20220323_140240_copy_1011x671.jpg

  • Like 1

Share this post


Link to post
Share on other sites

I needed some seats now for Trish and The Undertaker, I was going to go for some scale bucket seats from Killerbody but didn't think they suit the beach buggy look, then realised I had two perfectly good seats from the section I removed from the body, they needed a bit of filling as they have a raised section that needed removing.

20220322_204630_copy_1074x604.jpg

20220322_205338_copy_1191x670.jpg

20220322_205310_copy_632x1123.jpg

  • Like 3

Share this post


Link to post
Share on other sites

To animate the driver I made him a separate cockpit that has all the servos attached and can be removed from the chassis if any work is need on it, again 2mm styrene sheet was used to construct. A servo for the steering wheel, one for the accelerator pedal and one for the gear shift where installed and The Undertaker suitably placed in his new seat. 

Trish lost her legs for the moment and received a tiny 1.7 gram servo in her back for her arm and another servo to enable her upper body to turn

 

20220329_225327_copy_967x544.jpg

20220329_225343_copy_940x529.jpg

20220329_230225_copy_1048x590.jpg

  • Like 5

Share this post


Link to post
Share on other sites

Other Sand Rover conversions I'd seen used a cut down SRB rear roll bar hoop bit I really didn't want to chop up any of my original ones, I could have got a re-release one but instead I went a different route.

I had Ford Ranger Rear roll hoop which are a lot shorter, so I fitted this and then used the original Sand Scorcher rear body clip to fasten to the Ford Ranger hoop. It sticks up a little but I can live with that as it's easily accessible and uses original parts.

I have an original Super Champ front servo saver fitted and used a cut down plastic body post extension over the top of the original SC post.

Battery placement was going to be in the original position but I found it would be a pain to remove easily with all the wiring for the animation servos in the way so have decided to use a shorty lipo mounted on it's side just in front of the roll bar hoop, it fits really nicely here and with a couple of notches out of the rear of the underbody fits in snuggly.

With the battery mounted sideways it stopped the main body from sitting on the chassis so again out came the Dremel and a suitable hole was relieved for the battery to poke through. I then made a cardboard template and transfered this to some styrene sheet to make a cover for the new battery position.

inbound503443870722285720.jpg

inbound2960343861421855116.jpg

inbound3323745619903677188.jpg

  • Like 1

Share this post


Link to post
Share on other sites

Now I don't know why I have never seen this before but a couple of weeks ago I came across a picture of a beach buggy. Turns out it was driven by Steve McQueen in the 1960s version of The Thomas Crown Affair. 

I just love those headlights! So out came the Dremel.... again.

I designed a light pod and 3d printed a couple of them. 

Screenshot_20220410-174837_Chrome.jpg

20220411_115318_copy_1053x593.jpg

20220411_110013_copy_1005x566.jpg

20220411_115310_copy_1093x615.jpg

20220411_122918_copy_878x759.jpg

  • Like 2

Share this post


Link to post
Share on other sites

One thing that just didn't look right to me was the long 'snoot' at the front. I don't need the extra length here as the SRB front suspension is about 15mm further back. 

Guess what? 

Dremel time!!! 😂😂

I also removed the part on the inner wheel arch that used to be the mounting point for the original Sand Rover light pods

20220413_145011_copy_1082x609.jpg

20220413_145130_copy_1033x581.jpg

20220413_152438_copy_990x557.jpg

20220413_180722_copy_959x540.jpg

20220413_223859_copy_1319x743.jpg

20220413_224726_copy_1164x655.jpg

  • Like 2

Share this post


Link to post
Share on other sites

Thats well cool , would be nice to have Steve in the driving seat again , not sure if they are available though .

Great work there .

  • Like 1

Share this post


Link to post
Share on other sites

Today's body mod is the transition between the bulkhead and body, the straight down body line just doesn't fit with swoopy body work so I made a couple of inserts from 2mm styrene to add a curved transition 

20220416_220649_copy_895x796.jpg

20220416_220658_copy_1033x581.jpg

20220416_223954_copy_1021x574.jpg

  • Like 2

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Today's Birthdays

    1. Dusty1 (56 years old),
    2. jlcox7 ,
    3. mastino
  • Member Statistics

    59080
    Total Members
    2639
    Most Online
    Tino22
    Newest Member
    Tino22
    Joined
×
×
  • Create New...