JezHall 8 Posted May 17, 2022 Is there an easy fix or a replacement part for a broken front shock mount tower on a TL-01? Its broken where the top screw bolts through. Strangely this is part of the chassis ????? Any ideas welcome! Thanks in advance Share this post Link to post Share on other sites
KEV THE REV 2319 Posted May 17, 2022 Any pics of the damage ? . If it is cracked ,you could try strong styrene glue and drill drough the screw hole and use a nut and bolt / washers and a sleeve instead of the self tapper step screw . I would carry out the same process for the other upper damper mounts too to relieve stress Share this post Link to post Share on other sites
JezHall 8 Posted May 17, 2022 10 minutes ago, KEV THE REV said: Any pics of the damage ? . If it is cracked ,you could try strong styrene glue and drill drough the screw hole and use a nut and bolt / washers and a sleeve instead of the self tapper step screw . I would carry out the same process for the other upper damper mounts too to relieve stress Not great pics but you can see where it snapped. The rear ones had hairline cracks....you can see where i drilled and cable tied them (after gluing) Seems to be a weak spot so I wondered if a fix exists before i try to fabricate something from aluminium........? Share this post Link to post Share on other sites
Superluminal 3750 Posted May 17, 2022 This is one of the flaws of the TL01 sadly. You can repair as above or replace the chassis halves - bit of a ball ache in rebuilding it but fortunately they are readily available and not too expensive. 1 Share this post Link to post Share on other sites
KEV THE REV 2319 Posted May 17, 2022 There are some 3D printed repair parts available, like this for instance :- https://upgradeparts.com/2020/07/17/tl01-replacement-front-shock-tower/ I would go with fabbing up my own alu plates across the front and back of the tower 1 Share this post Link to post Share on other sites
JezHall 8 Posted May 17, 2022 10 minutes ago, KEV THE REV said: There are some 3D printed repair parts available, like this for instance :- https://upgradeparts.com/2020/07/17/tl01-replacement-front-shock-tower/ I would go with fabbing up my own alu plates across the front and back of the tower That looks quite thick........I might try it with the aluminium. It might sit nicely behind the bumper screws? 2 Share this post Link to post Share on other sites
Mad Ax 9313 Posted May 18, 2022 Have a look at these diagrams. For M03 / FF02, but the chassis are very similar, this will give you an idea of how you can make a brace to reinforce the shock towers. https://www.fibre-lyte.co.uk/fl/cars/tamiya/m03ff02.html I have the parts above but have never tried them on a TL01. If I get time later I'll see if they will fit (there is a discussion on here from over 10 years ago about making M03 tower braces fit a TL01 but the results are inconclusive). 1 1 Share this post Link to post Share on other sites
JezHall 8 Posted May 18, 2022 As a quick fix I used some plastic repair paste....it's not the best looking fix but at least it will get it running for now.... Share this post Link to post Share on other sites
JezHall 8 Posted May 18, 2022 12 hours ago, Mad Ax said: Have a look at these diagrams. For M03 / FF02, but the chassis are very similar, this will give you an idea of how you can make a brace to reinforce the shock towers. https://www.fibre-lyte.co.uk/fl/cars/tamiya/m03ff02.html I have the parts above but have never tried them on a TL01. If I get time later I'll see if they will fit (there is a discussion on here from over 10 years ago about making M03 tower braces fit a TL01 but the results are inconclusive). First 3 attempts............ 2 Share this post Link to post Share on other sites
No Slack 454 Posted May 19, 2022 A common problem with the TL01 chassis. A brace is a good idea. ( Tip: Check the front tires as the thread seems tot point in the wrong direction.) 1 Share this post Link to post Share on other sites
KEV THE REV 2319 Posted May 19, 2022 Coming along . When I make things from alu sheet I cover the area I want to cut out with masking tape , this helps to measure & draw the item and protects it when cutting / drilling / filing / using vice etc 1 Share this post Link to post Share on other sites
JezHall 8 Posted May 19, 2022 15 hours ago, No Slack said: A common problem with the TL01 chassis. A brace is a good idea. ( Tip: Check the front tires as the thread seems tot point in the wrong direction.) 15 hours ago, No Slack said: A common problem with the TL01 chassis. A brace is a good idea. ( Tip: Check the front tires as the thread seems tot point in the wrong direction.) Just noticed Thanks for that! Share this post Link to post Share on other sites
JezHall 8 Posted May 19, 2022 14 hours ago, KEV THE REV said: Coming along . When I make things from alu sheet I cover the area I want to cut out with masking tape , this helps to measure & draw the item and protects it when cutting / drilling / filing / using vice etc I will do for the final version. Still trying to get the holes aligned I was going to put a carbon fibre look wrap on it.....if i ever finish it! Share this post Link to post Share on other sites
KEV THE REV 2319 Posted May 20, 2022 10 hours ago, JezHall said: Still trying to get the holes aligned That's why I use tape . I can measure & draw the whole item and plot the hole centres then centre punch the holes to get an acuate position before drilling Share this post Link to post Share on other sites