TurnipJF 9192 Posted October 25, 2018 Made a start with this: It will be the "dress uniform" for my TB-03. Masking and paint tomorrow if the weather holds! 5 Share this post Link to post Share on other sites
krisby 89 Posted October 26, 2018 did 3 coats on the sand scorcher body that is intended for my spare hornet chassis (once I work out how to mount the body). 7 Share this post Link to post Share on other sites
krisby 89 Posted October 26, 2018 I also did a matt black job on the hornet shell, vintage chassis but body was rough as guts. Share this post Link to post Share on other sites
krisby 89 Posted October 26, 2018 and plopped MSC back in the fox ready to shelf her. Share this post Link to post Share on other sites
krisby 89 Posted October 26, 2018 and I bought a few paint pots at lunchtime today so I can start painting the detail on Scorcher, including Sand Scorcher Steve and his steering wheel. So once body done, still need to come up with best solution for mounting on the hornet chassis. Share this post Link to post Share on other sites
a.w.k. 665 Posted October 26, 2018 My son and me started an youtube channel for our rc activities. We are new to that, so still learning.... https://www.youtube.com/channel/UCDYtZu7ydklEOoKTqGb0Jog?app=desktop 1 Share this post Link to post Share on other sites
jupitertwo 1484 Posted October 26, 2018 On 10/24/2018 at 2:06 AM, Re-Bugged said: That is great bang for your buck there Looks similar to the Metallic Plasma Edge 2. Yeah, great little buggies for light bashing. It's resting now at the in-laws holiday home, till either I return or the nephew/nieces find it. I'll have to look up how to lock/slow the diff on it, as it was great fun in the gravel back yard, but did get stuck a few times. I was wondering about those metallic plasma edges, I'll be very tempted by one of those I think should an offer come around. 3 Share this post Link to post Share on other sites
Mad Ax 9313 Posted October 26, 2018 Found a break in the rain to that Hopup and Homebrew out to a nearby wooded area for some back-to-back tyre comparisons. Updates in the project thread later. 1 Share this post Link to post Share on other sites
TurnipJF 9192 Posted October 26, 2018 Masked and painted the Arta Garaiya shell that came with my TB-03: At first I was very unimpressed with the coverage of the bright red paint, which seemed pretty translucent even after using up the whole can. However once it was backed with white it looked a lot better, and when that was in turn backed with silver it looked pretty darn good if I may say so myself. One of the tricky parts of doing a multipart body shell like this one is to get the colour saturation on the different parts to match. To this end I was very careful to make the same number of passes with the spray can on both the main shell and the tail section, to make sure that they were as close as possible. I think it turned out alright. 9 1 Share this post Link to post Share on other sites
ChrisRx718 4470 Posted October 27, 2018 Took some photo's : 15 1 Share this post Link to post Share on other sites
Nicadraus 6198 Posted October 27, 2018 Beautiful cars and off-roaders Chris! Nicely done details. Share this post Link to post Share on other sites
Nicadraus 6198 Posted October 27, 2018 Did a carbon fiber rear body post stiffener. Also improved the temporary rear shock tower while waiting for the 3mm board I ordered to replace it. 8 Share this post Link to post Share on other sites
Re-Bugged 10146 Posted October 27, 2018 Nice photography & subjects @ChrisRx718, gotta be happy with that Share this post Link to post Share on other sites
Re-Bugged 10146 Posted October 27, 2018 3 hours ago, Nicadraus said: Did a carbon fiber rear body post stiffener. Also improved the temporary rear shock tower while waiting for the 3mm board I ordered to replace it. Smart. If you can't buy it, make it 1 1 Share this post Link to post Share on other sites
Re-Bugged 10146 Posted October 27, 2018 After what seemed like a life time of prepping, deciding, cutting out window masking and applying some additional masking, it was a relief to eventually let some Spaz Stix Black out the can. 5 Share this post Link to post Share on other sites
ThunderDragonCy 7878 Posted October 27, 2018 @ChrisRx718 Love the silver offroader and the Skyline. Very very nice. Share this post Link to post Share on other sites
Nicadraus 6198 Posted October 27, 2018 2 hours ago, Re-Bugged said: Smart. If you can't buy it, make it Yup! Share this post Link to post Share on other sites
Ray_ve 1043 Posted October 27, 2018 Found my old Nitro racer, a Mugen Seike Prime 12 chassis I believe. I'm not going to run nitro again, so perhaps this is a nice base for a brushless conversion! 8 1 Share this post Link to post Share on other sites
Fabia130vRS 2098 Posted October 27, 2018 Today my DF02 got new CVA dampers and a YR Racing red alu prop shaft. Now waiting for the 4370 brushless combo, 3s battery and TX/RX also my best driving buddy got his new Tamiya Touring Car in the mail, immediately went for a drive, he bought a TB04, we were quite amazed, I didnt knew the tb04 has oil diffa. His car was equipped with a Reedy Conquest 19T, 1060 esc and 2 s lipo, with standard 25T and 66T gearing. my TA05 IFS has a bit worn out belts, top speed was lower then last time. I did a 53kph while his on brushed did 42kph. Still amazing how those two handle. 6 1 Share this post Link to post Share on other sites
TurnipJF 9192 Posted October 27, 2018 Put some decals on the Arta Garaiya shell: I'd say it's about two thirds done. 13 Share this post Link to post Share on other sites
Jason1145 3986 Posted October 27, 2018 I’ve got to stop liking stuff in this thread but it’s so hard! 4 Share this post Link to post Share on other sites
Re-Bugged 10146 Posted October 27, 2018 13 hours ago, Ray_ve said: Found my old Nitro racer, a Mugen Seike Prime 12 chassis I believe. I'm not going to run nitro again, so perhaps this is a nice base for a brushless conversion! Nice. @novicelad converted his TXT Nitro Truck to brushless with great success. Starting to ponder converting my 1/8 buggy to, as the local nitro supplier has shut and is a 240km round trip to the next nearest one. 2 Share this post Link to post Share on other sites
Re-Bugged 10146 Posted October 27, 2018 8 hours ago, Jason1145 said: I’ve got to stop liking stuff in this thread but it’s so hard! But that’s why we’re all here, coz we like it 👍🏻😁 1 Share this post Link to post Share on other sites
yogi-bear 2321 Posted October 28, 2018 did a halloween comp entry, a 3D printed monster body onto a Lunchbox chassis. I had to modify it a bit to get it to fit the chassis properly. I also managed to get some time to work on my Escort Mark 2 project. I want to make a metal chassis and add some detail. So have sorted out most of the base now, added some aluminium mounting blocks for the TA02 front and rear gear boxes. Also made up a custom dash and fitted a micro servo to drive the steering well. I'll also do a aluminium roll cage as that will give the middle some extra strength and stop some flexing. Here you can see the servo under the dash and I've started making the firewall. Still need to add in the rear wheel arches and strengthening bars to stiffen the chassis and mount the roll cage too. I found some 4 cycle engine parts on thingiverse, so my idea is to use bits to cover up the TA02 gear box. It's a pity the shock towers are so far in, but that will have to do for now. 12 2 Share this post Link to post Share on other sites
Peter_B 997 Posted October 28, 2018 16 minutes ago, yogi-bear said: did a halloween comp entry, a 3D printed monster body onto a Lunchbox chassis. I had to modify it a bit to get it to fit the chassis properly. I also managed to get some time to work on my Escort Mark 2 project. I want to make a metal chassis and add some detail. So have sorted out most of the base now, added some aluminium mounting blocks for the TA02 front and rear gear boxes. Also made up a custom dash and fitted a micro servo to drive the steering well. I'll also do a aluminium roll cage as that will give the middle some extra strength and stop some flexing. Here you can see the servo under the dash and I've started making the firewall. Still need to add in the rear wheel arches and strengthening bars to stiffen the chassis and mount the roll cage too. I found some 4 cycle engine parts on thingiverse, so my idea is to use bits to cover up the TA02 gear box. It's a pity the shock towers are so far in, but that will have to do for now. What are the wheels you have on the Escort? I'm looking for some similar to those butvM chassis size. 1 Share this post Link to post Share on other sites