silvertriple 3557 Posted September 18, 2021 Started the Turbo Optima built this morning... Maybe possible to make a spot the differences game with the pictures of the Javelin build 7 Share this post Link to post Share on other sites
Superluminal 3750 Posted September 18, 2021 Painted the driver for a Turbo Tomahawk build that I finished this morning. Cant seem to flatten off the yellow sticker on the steering wheel though. Might cut it off or paint it black. 7 1 Share this post Link to post Share on other sites
Willy iine 18806 Posted September 18, 2021 2 hours ago, Superluminal said: Painted the driver for a Turbo Tomahawk build that I finished this morning. Cant seem to flatten off the yellow sticker on the steering wheel though. Might cut it off or paint it black. Good job. On the yellow, did you try using some heat to get the decal to stretch and contour? If not I would gently remove it, then reapply using an emboss heat gun and silicon squeegee. Hairdryer will also work, just more air flow vs heat gun. GL! 1 Share this post Link to post Share on other sites
silvertriple 3557 Posted September 18, 2021 6 hours ago, Superluminal said: Painted the driver for a Turbo Tomahawk build that I finished this morning. Cant seem to flatten off the yellow sticker on the steering wheel though. Might cut it off or paint it black. That is the typical reason why I prefer go paintjob rather than stickers. Your driver's helmet and face are superb! This is the driver of my Javelin (only stickers are applied on the Helmet: the visor made using part of the Kyosho sticker and the small Kyosho sticker). In the meantime, I progressed on the Turbo Optima in the afternoon. Status of the operations as of the time I was due to free the table I will update the thread, but probably not right now... (well, it's updated :-D )- you may find it in Kyosho corner) 2 1 Share this post Link to post Share on other sites
TurnipJF 9192 Posted September 18, 2021 Been a fairly productive day, did a bit of work on the widened rear arches of my next teapot racer project: Fitted nice shiny red shocks to my Rookie Rabbit: Trimmed and painted the new shell for my TT-01: Progress was halted when my can of PS smoke gave up the ghost partway through the first coat. Another is on order... 6 Share this post Link to post Share on other sites
Nikko85 3453 Posted September 18, 2021 Project 1/14 Tamiya MF-O1x got most of the way there 186 mm wheelbase custom cutdown prop shaft, the rest is a MF-01x, but with a 1/14 Pick up body. 7 Share this post Link to post Share on other sites
Willy iine 18806 Posted September 18, 2021 31 minutes ago, Nikko85 said: Project 1/14 Tamiya MF-O1x got most of the way there 186 mm wheelbase custom cutdown prop shaft, the rest is a MF-01x, but with a 1/14 Pick up body. For a second I thought that owl (?) in the second picture looked like it was giving us the birdie. Nice job on the truck. 2 Share this post Link to post Share on other sites
nel33 870 Posted September 18, 2021 I removed the rear gearbox and suspension assembly from Manta chassis. Had an idea right after that as I wasn't able to find a quality red anodized drive shaft. Have the blue bling tamiya one and a can of ts18? Red metallic that I used for rim highlights and thought it would be a waste to not use it a bit more of that paint. After a quick trip to the maze that calls itself a Scandanavian budget furniture store I painted the other side of the drive shaft. I left the end of the dog bones blue as I can't bother to de-anodize the shaft and red paint would wear off anyway. 4 Share this post Link to post Share on other sites
Willy iine 18806 Posted September 18, 2021 Rough test fit today. Will glue these pieces together tonight. Update now glued.. will heat form, sand, and putty tomorrow. 10 Share this post Link to post Share on other sites
InsaneJim69 1584 Posted September 18, 2021 Nothing R/C for me, was going to rewire a nerf gun until I have been called out 4 times for Hydrogen bus issues (my actual job) . Typically it's a CTRL, ALT and ...... You get the point. 😂😂👍 Share this post Link to post Share on other sites
Rider400 353 Posted September 18, 2021 Trying something different with an ORV... 3 Share this post Link to post Share on other sites
markbt73 5316 Posted September 18, 2021 Did you ever notice how much of this hobby is literally watching paint dry? 2 1 Share this post Link to post Share on other sites
Original Jardasius 97 Posted September 18, 2021 19 minutes ago, markbt73 said: Did you ever notice how much of this hobby is literally watching paint dry? Indeed it is but hey if ya sniff it you get a free bonus tho eh? Share this post Link to post Share on other sites
Original Jardasius 97 Posted September 18, 2021 Not a whole lot done today organized parts and boxes for this winter & spring builds, cleaning up the office and talking to my woman as I type this Share this post Link to post Share on other sites
Rider400 353 Posted September 18, 2021 1 hour ago, Willy iine said: Rough test fit today. Will glue these pieces together tonight. Update now glued.. will heat form, sand, and putty tomorrow. This is too f'n cool! 4 1 Share this post Link to post Share on other sites
nel33 870 Posted September 18, 2021 slightly stressed in swapping out the gear box parts. taking alot of time to avoid scarfing the plastic on the 2 covers of the gearbox. removed the tires/shocks and suspension arms in 1 go and let the dog bones fall out. 1hr later... the rear gearbox is rebuilt with the new casing and all went fine, still stressful AH to avoid scarfing but now i just need to address the scarfed hole mounts for the rear on the tub and pick up the selftappers. when im happy there is no play in the chassis/gearbox mount i will put in the electronics in the tub and then find time to stretch its legs. this is nearing the end of the manta saga though i do have some custom stickers planned for it. Share this post Link to post Share on other sites
Ferruz 11702 Posted September 19, 2021 Got the new lights for the Hornet today, a few modifications and they are on! Quite happy with the rear ones, they are better than ever before 6 Share this post Link to post Share on other sites
ImALlama 1370 Posted September 19, 2021 Lots done today, started by cleaning my TRF102 and put new stupidly expensive bearings in it (I prob won’t even notice a difference ). Tried to fix my dads 4wd torment but found out I need to order some more parts, then I updated the electronics in his clod. The silver can f1s body has been sitting partially painted for a few weeks now, so I continued that so I can get back to trying for 50mph again. Then decided to make the P34 a silver can speed run car, so I put electronics in it (it’s been sitting with nothing in it for quite some time). Since I was already painting and a grasshopper showed up, I decided to paint it (nothing special, all one color using whatever ts paint I had on hand, lime green or black, I need to stock up on more choices). It’s the first time I’ve painted a body before building the car, I think I might do this more often. Then I decided to build it. 5 Share this post Link to post Share on other sites
Rider400 353 Posted September 19, 2021 Finally getting around to wrapping this up. Started with the aluminum wheels and CCP chassis I got in a pile of stuff off ebay a few weeks back. Had something in mind with aluminum parts but that all changed when I found a donor Super BF for the front and rear end. (I secretly want an RC10T Monster so I kinda had that in mind with this build) I couldnt source a BF body but I found a Associated truck body that is pretty identical minus the windows. Using magnet mounts theyre actually pretty rad the thing just snaps in place. And best part is Ill just get some more magnets to run my Pumkin body when I feel like it. The front pin is setup to adjust height easily. Newer electronics. I know shocks are upside down but front end is frankensteined with Super parts and standard BF parts and it doesnt like the shocks mounted other way for some reason. Body needs some stickers but its 99% done. Will run it tomorrow and see if anything needs changing. 8 Share this post Link to post Share on other sites
GeeWings 2830 Posted September 19, 2021 The weather has been rubbish so still haven’t painted the Egress’ wing but couldn't keep it clean any longer! We have a little park down the road with a perfect loose gravel path! My daughter was a nervous but excited driver… 4 Share this post Link to post Share on other sites
Grumpy pants 4485 Posted September 19, 2021 2 hours ago, Rider400 said: Finally getting around to wrapping this up. Started with the aluminum wheels and CCP chassis I got in a pile of stuff off ebay a few weeks back. Had something in mind with aluminum parts but that all changed when I found a donor Super BF for the front and rear end. (I secretly want an RC10T so I kinda had that in mind with this build) I couldnt source a BF body but I found a Associated truck body that is pretty identical minus the windows. Using magnet mounts theyre actually pretty rad the thing just snaps in place. And best part is Ill just get some more magnets to run my Pumkin body when I feel like it. The front pin is setup to adjust height easily. Newer electronics. Body needs some stickers but its 99% done. Will run it tomorrow and see if anything needs changing. Very nice 💥 2 Share this post Link to post Share on other sites
djmcnz 754 Posted September 19, 2021 1 hour ago, GeeWings said: The weather has been rubbish so still haven’t painted the Egress’ wing but couldn't keep it clean any longer! We have a little park down the road with a perfect loose gravel path! My daughter was a nervous but excited driver. That's brave with the solid curb! Hold the phone the right way next time, we see the world in widescreen after all. 😉 Share this post Link to post Share on other sites
GeeWings 2830 Posted September 19, 2021 35 minutes ago, djmcnz said: That's brave with the solid curb! Hold the phone the right way next time, we see the world in widescreen after all. 😉 Yes, was a bit nervous but the Egress actually clears the curb in this location. Point taken with the phone although I was a bit distracted 1 Share this post Link to post Share on other sites
Nicadraus 6198 Posted September 19, 2021 Updated the XV's spur (77t) and pinion (26t) to 48p (not .6) 4 Share this post Link to post Share on other sites
Superluminal 3750 Posted September 19, 2021 Finished a Turbo Tomahawk build. Kyosho never made an official enhanced Tomahawk like they did with the Scorpion and Optima that im aware of so I gave it a go. Its basically a half Turbo Scorpion and Half Tomahawk. Its built with; Tomahawk chassis rails and radio plates, body shell and cockpit. Turbo Scorpion gear box, steering, suspension mounts and longer wheelbase rear chassis plates. Scorpion HG wing mount and Javelin wing. Turbo Optima front gold shocks all round (probably need softer springs for front and stiffer rears i think) Kyosho G15 15t motor, HW1060, Absima receiver and Savox servo. 19 1 Share this post Link to post Share on other sites