evssv69 378 Posted February 5, 2019 for rear of madcap..90mm...I`m pretty sure this is the length It needs .....also sum front ones pls..thk there 70mm... Share this post Link to post
graemevw 821 Posted February 5, 2019 There is a set off an astute on uk ebay. Share this post Link to post
Tamiyabigstuff 830 Posted February 5, 2019 I have a few used yellow CVA dampers around somewhere - will have a look tomorrow for them. They are all from cars I've taken apart over the years so might need a clean. 1 Share this post Link to post
evssv69 378 Posted February 5, 2019 7 hours ago, graemevw said: There is a set off an astute on uk ebay. hes jus tolds me this.. Hi Mike, The fronts are 65mm eye center to eye center give or take a mm The rears are 85mm eye center to eye center give or take a mm I measured with a ruler and by eye but pretty much thats the sizes, Share this post Link to post
evssv69 378 Posted February 5, 2019 39 minutes ago, Tamiyabigstuff said: I have a few used yellow CVA dampers around somewhere - will have a look tomorrow for them. They are all from cars I've taken apart over the years so might need a clean. cleaning not a problem dude....thk u for looking.... Share this post Link to post
Tamiyabigstuff 830 Posted February 6, 2019 Well, I found the bag of dampers but none are the lengths you are looking for. 1 Share this post Link to post
evssv69 378 Posted February 6, 2019 28 minutes ago, Tamiyabigstuff said: Well, I found the bag of dampers but none are the lengths you are looking for. Typical.. .....Well i apperacte u looking.......guess there not remotely close then??. Share this post Link to post
Tamiyabigstuff 830 Posted February 6, 2019 2 hours ago, evssv69 said: Typical.. .....Well i apperacte u looking.......guess there not remotely close then??. Close-ish - probably within 10mm - is that close ? Overall damper length can be played around with by using different length piston rods, plastic eye ends and spacers. 1 Share this post Link to post
evssv69 378 Posted February 6, 2019 9 hours ago, Tamiyabigstuff said: Close-ish - probably within 10mm - is that close ? Overall damper length can be played around with by using different length piston rods, plastic eye ends and spacers. Pm sent Share this post Link to post
graemevw 821 Posted February 12, 2019 Once again there is yet another astute set on uk ebay, if you can make the lengths work (i assume they are a tiny bit short like the last astute ones). 1 Share this post Link to post
evssv69 378 Posted February 12, 2019 1 hour ago, graemevw said: Once again there is yet another astute set on uk ebay, if you can make the lengths work (i assume they are a tiny bit short like the last astute ones). I'll chk em out Share this post Link to post
max69vk 708 Posted February 12, 2019 I’ve just done a bit of digging through all my CVA’s, and of 20+ pairs I’ve found one set 65mm between the eyes, & one set 85mm between the eyes! 1 Share this post Link to post
evssv69 378 Posted February 13, 2019 13 hours ago, max69vk said: I’ve just done a bit of digging through all my CVA’s, and of 20+ pairs I’ve found one set 65mm between the eyes, & one set 85mm between the eyes! How much pls dude.. Share this post Link to post
max69vk 708 Posted February 13, 2019 53 minutes ago, evssv69 said: How much pls dude.. Make me an offer! I need to get my hands on a set of mini CVA’s so if you’ve got any of them maybe we could work something out 😁 1 Share this post Link to post
evssv69 378 Posted February 13, 2019 Tbh i dont have hardly any tamiya parts here.....I'll pm u dude Share this post Link to post