bjorklo 1620 Posted February 22, 2019 35 minutes ago, Honza said: Aren't blue knuckles TA02 part, meant for "long span" front suspension arms? I think that TA01 suspension uses DF01 knuckles. Sorry I don't know. I guess you are correct. I think previous owner might have done a mod. Share this post Link to post Share on other sites
svenb 3778 Posted February 22, 2019 As far as I know ta02 blue knuckles are the same as ta03 black/grey knuckles, do if you have blue Honza is right you have the long span suspension set. Share this post Link to post Share on other sites
Tizer 606 Posted February 22, 2019 You can use black DF01 or Hummer knuckles TA02/TA03/CC01 knuckles are the same and are different from TA01/DF01. On the TA02 they are used with longer lower arms to reduce the scrub radius of the front wheels. TA02W actually has TA01 knuckles but with TA02 arms to increase the track width but it needs special (longer) shafts.@bjorklo I meant the rear knuckles, not the arms. The knuckles have 1.5 degrees of toe-in built in and should be mounted the right way round otherwise you'll end up with toe-out which handles very poorly and a slightly off wheelbase. Yours actually are mounted correctly, it just looks funny with the spacers for the adjustable turnbuckles. Share this post Link to post Share on other sites
bjorklo 1620 Posted February 22, 2019 5 hours ago, Tizer said: You can use black DF01 or Hummer knuckles TA02/TA03/CC01 knuckles are the same and are different from TA01/DF01. On the TA02 they are used with longer lower arms to reduce the scrub radius of the front wheels. TA02W actually has TA01 knuckles but with TA02 arms to increase the track width but it needs special (longer) shafts.@bjorklo I meant the rear knuckles, not the arms. The knuckles have 1.5 degrees of toe-in built in and should be mounted the right way round otherwise you'll end up with toe-out which handles very poorly and a slightly off wheelbase. Yours actually are mounted correctly, it just looks funny with the spacers for the adjustable turnbuckles. Is them like this so the different size ball-bearings will fit? Ahh, I c... Good thing that they are the correct way. Share this post Link to post Share on other sites
Honza 937 Posted February 22, 2019 These are TA02/03/CC01 knuckles. They give you ~10mm narrower front, if you use them with TA01 arms. DF01/TA01 use two 1150 and same wheel axles as rear hubs. 1 Share this post Link to post Share on other sites
bjorklo 1620 Posted February 23, 2019 12 hours ago, Honza said: These are TA02/03/CC01 knuckles. They give you ~10mm narrower front, if you use them with TA01 arms. DF01/TA01 use two 1150 and same wheel axles as rear hubs. Thanks for that info.. Then I will go ahead and get the black ta03 knuckles... Share this post Link to post Share on other sites
Tizer 606 Posted February 24, 2019 On 2/23/2019 at 9:55 AM, bjorklo said: Thanks for that info.. Then I will go ahead and get the black ta03 knuckles... Do you want a narrow front? Since the yellow arms you're using are TA01 arms, you'll need TA01 (DF01) knuckles. (+ axle and extra 1150 bearings) The old TA02 knuckles you have will fit but your dogbone axle will be too long and won't fit. 1 Share this post Link to post Share on other sites
neverfollow 599 Posted February 24, 2019 I've never seen the parts in yellow before..very cool! Share this post Link to post Share on other sites
bjorklo 1620 Posted February 24, 2019 7 hours ago, Tizer said: Do you want a narrow front? Since the yellow arms you're using are TA01 arms, you'll need TA01 (DF01) knuckles. (+ axle and extra 1150 bearings) The old TA02 knuckles you have will fit but your dogbone axle will be too long and won't fit. Now I understand... I thought arms were the same length.. Then I will see what I have in my spare parts box, I think the only thing I might need is the axle. Thanks for not giving up 1 Share this post Link to post Share on other sites
bjorklo 1620 Posted February 24, 2019 I dyed the yellow dampers black, using Rit dye. I wish all tamiya parts would take dye it would have been so much fun.. Or at least Tamiya could have released all the parts in white hop-up parts, so we could have dyed them as we please. Next is to finish the front suspension and steering. 5 Share this post Link to post Share on other sites
Rich_8717 114 Posted February 25, 2019 Look great, I like seeing your builds so thanks for sharing. The Jagermeister shell is a classic, but the yellow Auto Tech M3 body set would be cool to see on the yellow chassis! 1 Share this post Link to post Share on other sites
bjorklo 1620 Posted February 26, 2019 16 hours ago, Rich_8717 said: Look great, I like seeing your builds so thanks for sharing. The Jagermeister shell is a classic, but the yellow Auto Tech M3 body set would be cool to see on the yellow chassis! Glad you like it and that you like the builds I do. Yeah it would have been pretty cool to have the yellow Auto Tech M3 body. Just a quick search on ebay, I could only see the decals but they were crazy expensive. Don't think there is any reproductions to get either.. Share this post Link to post Share on other sites
bjorklo 1620 Posted February 26, 2019 I search through my parts box and guess what, I found all the parts I need to finish the front suspension and steering. I even found some cool turnbuckle for the steering You can see that TA01 arms a quite a bit shorter on the length of the turnbuckle Finished assambled 1 Share this post Link to post Share on other sites
bjorklo 1620 Posted February 26, 2019 I consider this chassis done for now. I hope you have enjoyed this build. Next for this car is to add a driver and map reader and a light kit. Also it fine adjustments in setup. Since my original plan was to build a runner and there is now way I can get myself to run this, other than in my living room, I just might have to build myself a runner chassis 10 Share this post Link to post Share on other sites
bjorklo 1620 Posted February 27, 2019 I made this post picture for my webpage http://www.odd-arne.com 3 Share this post Link to post Share on other sites
Man1c M0nk3y 564 Posted February 27, 2019 Looks great 👍 1 Share this post Link to post Share on other sites
bjorklo 1620 Posted February 27, 2019 3 minutes ago, Man1c M0nk3y said: Looks great 👍 Thanks Share this post Link to post Share on other sites
bjorklo 1620 Posted March 14, 2019 Someone suggested that I should get some yellow wheels for this chassis, so I did. I think it looks really good. So I had to try the BMW M3 body on the chassis to see how it looks. To my big surprise, these wheels looks even better on than the bbs wheels. So these are now the main wheels for this car. I also added a cockpit to the body. This is the old one that was in the other body, but it will do for now. The chassis on my car of the week shelf. Share this post Link to post Share on other sites
svenb 3778 Posted March 14, 2019 Nice👍 I suppose the hunt is on for yellow electrics now! 1 Share this post Link to post Share on other sites
bjorklo 1620 Posted March 14, 2019 17 minutes ago, svenb said: Nice👍 I suppose the hunt is on for yellow electrics now! does that even exists? I guess I will have to paint electronics and change all the wiring to yellow, myself.. Share this post Link to post Share on other sites
svenb 3778 Posted March 14, 2019 14 minutes ago, bjorklo said: does that even exists? I guess I will have to paint electronics and change all the wiring to yellow, myself.. Looks like tamiya have released sets of yellow wheels, looks like they have been looking at this thread😉 1 Share this post Link to post Share on other sites
Tizer 606 Posted March 15, 2019 Neon yellow wiring does exist at least Not really a fan of the wheels. I feel like using knockoff wheels takes away from all the cool rare Tamiya parts that are on this car. Share this post Link to post Share on other sites
bjorklo 1620 Posted March 15, 2019 3 hours ago, Tizer said: Neon yellow wiring does exist at least Not really a fan of the wheels. I feel like using knockoff wheels takes away from all the cool rare Tamiya parts that are on this car. I c your point. To me that's not big deal.. I know myself how rare the parts are and how lucky I am to have them, so if I use another brand wheels, to get the total look I'm looking for, that's OK for me. Share this post Link to post Share on other sites
Honza 937 Posted March 16, 2019 On 3/15/2019 at 12:32 AM, bjorklo said: does that even exists? I guess I will have to paint electronics and change all the wiring to yellow, myself.. I think that Traxxas made yellow brushed ESC in the past. And I've seen Savox servo with yellow anodizing, but that won't be cheap Share this post Link to post Share on other sites
bjorklo 1620 Posted March 16, 2019 18 minutes ago, Honza said: I think that Traxxas made yellow brushed ESC in the past. And I've seen Savox servo with yellow anodizing, but that won't be cheap Thanks for the tip... Did a quick search and it's the xl5 esc from Traxxas that came in yellow. It would have been cool to have, but not sure if I'm going to add electronics to this car... Share this post Link to post Share on other sites