geniusanthony 361 Posted February 17, 2019 After waiting for far too long for one of these to be in stock, it finally arrived about a month ago. Had to actually finish a few things first but I actually sat down yesterday and got some progress. Bearings came in today so the rolling chassis is complete. I did another time-lapse of this one just like the Agrios, changed to a shot every 1 second instead of two. When the video is compiled I will put it up in here. Until then, here is a teaser of the cab mounted with the version 1 mount (its the green thing in the first pic) which as of now does allow the cab to tilt forward. Still need to draw up and print a rear body of I guess a support truck or a race truck, not sure which one yet. If you guys have any good 6x6 subjects to share I would love to see em. Cab is a Mercedes Actros 4143 for subject material. Also to do is re-profiling the front wheel cutouts and design/print off some flexible fender flares and or mudflaps. I might end up making some wheels as the aluminum set in front looks better proportioned to me and are approx 5 mm larger in diameter than the plastic set. Anyways, Enjoy! Tony 13 Share this post Link to post Share on other sites
87lc2 2666 Posted February 17, 2019 The tilt cab looks great on there. Also agree on the wheels, the fronts look really good. Share this post Link to post Share on other sites
Superluminal 3750 Posted February 17, 2019 This is what the dynahead should have been all along and not the yorkie easter egg box it turned out to be. 1 2 Share this post Link to post Share on other sites
geniusanthony 361 Posted February 17, 2019 From research there seems to be three basic styles, very few Mercs though, this one has an interesting history, it was an impostor race team smuggling drugs to a port. 3 Share this post Link to post Share on other sites
geniusanthony 361 Posted February 17, 2019 This is also a Merc but only two axles, the rear box has that gradual taper that is probably most recognizable. Share this post Link to post Share on other sites
geniusanthony 361 Posted February 17, 2019 Then there is this one, Maybe PDC took some liberties with this one, a whole lot more complex though, an '88 DAF X1 Turbotwin. Share this post Link to post Share on other sites
87lc2 2666 Posted February 17, 2019 I like all three examples, last one is pretty cool and haven't seen that before. I assume you're custom making the rear bed? Share this post Link to post Share on other sites
geniusanthony 361 Posted February 17, 2019 Got the truck all together and wouldn't you know it it was raining so all I could do was test a little bit in the garage. Neat truck though, goes over everything. Once it dries out here I will have to go for a proper drive. 6 Share this post Link to post Share on other sites
geniusanthony 361 Posted February 20, 2019 I am thinking that I need to move the cab back around 20mm and up around 5. At 20mm the back of the door will be nearly centered on the axle. Right now, with the current approach angle, a 75mm ledge will contact the body before the tires. These Bruder bodies are neat. I had hoped that I could disassemble the relevant bumper pieces and just keep what I will need. Instead it looks like I need to trim the body up to at least just below the second step. 2 Share this post Link to post Share on other sites
geniusanthony 361 Posted February 21, 2019 Got the cab moved back to where I wan t it. I am using some mounting buttons molded into the cab for mounting it. I wound up moving rearward 25 mm and up by 10 mm, the rear of the doors are now slightly behind the front axle which seems most appropriate. I printed the rear piece with the flares built in. Flares are 8mm wide and nearly cover the tires, perhaps 4 mm of tire sticks out. Humvee wheels are painted silver and though not as pretty as the aluminum set, will do for now. Still torn on what to do with the back half, without paint and sponsor decals it looks like a off-road garbage truck to my eye. I am pleased that the motor is less exposed with some cladding but I could do the same with a flatbed style as pictured further down, not sure yet what I prefer. I haven't had much luck in finding a group with a lot of pictures of this style of RC to peruse for ideas. I did find a neat video of a CR01 based 6x6, apparently stock parts can be combined to make the middle axle for both an input and output shaft if one were so inclined. I would have to look for the link. 3 Share this post Link to post Share on other sites
geniusanthony 361 Posted February 23, 2019 Made some more progress, Painted the Humvee wheels, still look too small. Designed and made a test part of a scale LMTV military 20 inch wheel. I hope it will look better once painted and detailed. Trimmed the body back, took a bunch of footage for a part 2 video on YouTube. Wheel wells now clear with room for flares under all suspension and steering movement. You can see a hint of the new wheels as well. Render attached for comments or improves the new wheel is slightly larger than the aluminum at the sidewall and about 28 mm wide for a less ballooned sidewall. Truck at top of cab is a substantial 260mm tall at this point, Agrios for scale. 2 Share this post Link to post Share on other sites
geniusanthony 361 Posted March 2, 2019 More work done on the Dynahead since last week, I relocated the receiver to under the cab, helps in making the wiring just a bit more sanitary. Last two days I have been designing the parts of the rear cage and learning how to print netting. I think that the overall design will be a modern Dakar rig, I am taking some liberties and picking my several favorite features. There aren't many Benz based trucks historically, much less 6x6's. May have been an easier choice if I had started with a MAN cab. These first two pics are linked from a scale model site, they were 1986 and year 2000 entrants. I find the below very interesting but complex and heavy. Here's a historical 6x6, doesn't really do it for me. Pardon the mess but here you can see the cage work I have done so far. Is strong enough and very light (mostly hollow) so quite at the start. Using all factory holes so no drilling required. If you look closely you can see two rails just outside the rear portion of the chassis which serve as the mounting points for the rest of the cage. I am trying out different ways to print a net for retaining the spare tires, it's not quite what I want yet. Also added a brushless, may try a slower one with a 20T to find a good compromise of control and speed. I have moved the receiver to under the cab on a little tray I made, the tray seals nicely with the inside of the cab to keep it relatively clean up there with good routing of the wires too. You can see the first version of the clear headlights mounted in the bumper, I need to tweak the CAD a bit and add bosses for led's. 6 Share this post Link to post Share on other sites
max69vk 708 Posted March 2, 2019 Ok, so this is a 2wd version but it’s what I’m basing mine on, maybe a few design ideas could be used on yours? 1 Share this post Link to post Share on other sites
geniusanthony 361 Posted March 2, 2019 1 hour ago, max69vk said: Ok, so this is a 2wd version but it’s what I’m basing mine on, maybe a few design ideas could be used on yours? Thanks for the share, that's pretty glorious. You say you are doing one as well, got a thread? I have the formers all done for the box, I'm going to try forming lexan for the sides of the box. Battery changes with the rear box are challenging. Have you worked out a method yet? I am printing some shorter formers (the hoops in the rear) presently. 1 Share this post Link to post Share on other sites
max69vk 708 Posted March 3, 2019 9 hours ago, geniusanthony said: Thanks for the share, that's pretty glorious. You say you are doing one as well, got a thread? I have the formers all done for the box, I'm going to try forming lexan for the sides of the box. Battery changes with the rear box are challenging. Have you worked out a method yet? I am printing some shorter formers (the hoops in the rear) presently. I’m only at the gathering parts stage at the moment, but I’ve been looking into it for months. I have no idea why but I’d never considered using hoops to support the rear body (seems quite obvious now though). I was considering making the rear panel either hinges at the top or halfway up so it can be flipped up for access & battery changes. Share this post Link to post Share on other sites
emory70 153 Posted March 7, 2019 I can't help but think a Dakar Garbage Truck would be crazy funny 1 Share this post Link to post Share on other sites
geniusanthony 361 Posted April 7, 2019 After much back and forth and trying several things I have finally made some reasonable progress on the back half. Sorry, no rally garbage truck, rather I have taken some inspiration from DAF TurboTwin X-1. Share this post Link to post Share on other sites
geniusanthony 361 Posted April 7, 2019 Body is fitted. Needs a lot of sanding, filler and details. Printed from pink ABS filament and sprayed with some cheap red enamel just to check the look. I had hoped to design a cage that I could fasten Lexan panels to, perhaps in version 2 once my Fusion 360 skills progress more. I had been mostly stalled on this one for the past weeks. If anyone fancies giving it a shot I can provide the .obj files. Until then, here is where it sits. I was able to solve the problem with keeping the battery accessible without removing the shell. Will post some more pics as progress continues. 6 Share this post Link to post Share on other sites
geniusanthony 361 Posted April 13, 2019 Progress. Rear shell is 2mm thick abs. Mounting is solid. I made modular mounting rails with standoffs for posts. Will update with more pics tomorrow, maybe even a proper video of how. Until then: I am not tied to the spare gas cans on the back. Just servo taped on for a bit of flair since I had them. Could also print a drop in bed in place of middle spare tire well, perhaps with random tools and things. 4 Share this post Link to post Share on other sites
geniusanthony 361 Posted April 13, 2019 Battery access is under the middle spare tire (above). Visible screws are temporary until replacement posts are installed. I am very please at this point. I will need advise on a front windshield I have flat .030 polycarbonate sheets though I don't know how I would pull one without a plug. The Actros body does not come with one. Also need to settle on a paint scheme. I don't have a decal package in mind yet for livery. I do have limited off cuts from other kits but no overall scheme in mind yet. Not tied to a color yet either if any enterprising individuals wished to offer a suggestion. 2 Share this post Link to post Share on other sites
JennyMo 3526 Posted April 13, 2019 Looking good! Screen Print Digital (on ebay) do a series of Dakar specific decal sheets - if you ask them nicely (like I did for the STUMPkamper) you can get them to change the numbers to the Truck Category (5xx) and also scale them slightly smaller (eg. 1/14th) to fit the panels on the truck more accurately. As for a colour, anything goes really - depending on the sponsors... Red Bull is a bit obvious really, although that always looks good - and the shape of the truck actually lends itself pretty well to the prancing bull and yellow circle? Being a Mercedes, then perhaps metallic silver as a base colour at least? Jx Share this post Link to post Share on other sites
emory70 153 Posted April 23, 2019 Looks super cool, but the location of the spare looks like it would be a nightmare to access if it were a real truck. I guess if I want an offroad garbage truck, I'll have to make my own! Share this post Link to post Share on other sites
geniusanthony 361 Posted May 27, 2019 Quick version of changes, 4700kv brushless Bruder cab, 3d print body mounts (existing holes, no chassis were harmed in the production of this model). Humvee 1.9 wheels 114mm tires 3d printed rear body custom formed acrylic windshield More details will come in a follow up vid. And she's done 4 Share this post Link to post Share on other sites
Bromley 681 Posted May 27, 2019 Tamiya, absolutely could do this sort of thing if they put there mind to it. What a brilliant take on the Dynahead chassis. Well done Sir! 1 Share this post Link to post Share on other sites
Busdriver 6209 Posted May 27, 2019 Love the video. I have a dynahead on order and am planning using a Unimog cab and a custom flat bed. Early in the build you mentioned tamiya Unimog wheels and tyres. Did they fit around the portals ok? Did you not like the look of them or just liked the look of the others? The ones that you ended up with are they the humvee beadlocks like the ones rc4wd stock? What tyres did you end up using? Sorry for so many questions once again loved the build. 1 Share this post Link to post Share on other sites