Nicadraus 6201 Posted February 20, 2023 Small detail update on the WO. Added the supplied silver dummy fog lamps Cut and installed this .5mm carbon fiber piece underneath the roof as a design and reinforcement as well. In the manual, it says to reinforce the body with sheets of small aluminum tapes. I decided to use the 0.5mm CF parts which were excess from the roof. NOw that's literally "reinforced". 7 Share this post Link to post Share on other sites
Nicadraus 6201 Posted March 6, 2023 Cut and shaped the 1mm carbon fiber side panel for the chassis of the WO. I will bolt this using M2 hex screws which I already purchased. 3 Share this post Link to post Share on other sites
Nicadraus 6201 Posted March 8, 2023 Some new parts WO came in today. Will be finishing this WO conversion and rebuild soon. Main chassis and roll cage. Ready for the build. 5 Share this post Link to post Share on other sites
Nicadraus 6201 Posted March 14, 2023 Yesterday, installed the CF side panels using M2 hex screws and nuts. Today, I started building the chassis. Used new metal servo saver and new steering rods No more worries of popping out as they are bolted with M2 hex screws.. Cleaned the gears and installed them with rubber-sealed bearings Fits perfectly Assembled the new roll cage. Installed the electronics 4 Share this post Link to post Share on other sites
Nicadraus 6201 Posted March 14, 2023 Test fitting... Will still work on the carbon fiber fins, make the lights work including the rear and install the antenna. 9 Share this post Link to post Share on other sites
Nicadraus 6201 Posted March 19, 2023 Fabricated the 1mm carbon fiber fins and installed it. Installed the rear lamps Cut and installed the screen on the sides... and also a small portion of the screen at the back. Next will be installing the LED bulbs and detail the driver's face and helmet while waiting for the front star-dish rims and tires. I already have the rear star-dish wheels. 3 Share this post Link to post Share on other sites
Nicadraus 6201 Posted March 24, 2023 Test fit of the rear star-dish while waiting for the arrival of the front wheels and tires. Share this post Link to post Share on other sites
ChrisRx718 4470 Posted March 24, 2023 Such a pretty buggy, I am so tempted by one of these to sit alongside my FAV but the BB01 is going to have to fulfill that role (as I've already pre-ordered and part-paid for it!) Not sure about the rims personally, some Kyosho Scorpion plated rims would really lift it and tie in with the other plated parts. Just to plant that seed... 2 Share this post Link to post Share on other sites
OldSchoolRC1 984 Posted March 24, 2023 Fantastic looking buggy, the silver parts completely transform the chassis. 1 Share this post Link to post Share on other sites
Nicadraus 6201 Posted March 25, 2023 13 hours ago, ChrisRx718 said: Such a pretty buggy, I am so tempted by one of these to sit alongside my FAV but the BB01 is going to have to fulfill that role (as I've already pre-ordered and part-paid for it!) Not sure about the rims personally, some Kyosho Scorpion plated rims would really lift it and tie in with the other plated parts. Just to plant that seed... I actually like this from the Kyosho Tomahawk. But I will have to change the front upright and retrofit in the WO which is doable. I've seen an aluminum silver star-dish but the price is just crazy. $60 + shipping for the rims only. Share this post Link to post Share on other sites
Nicadraus 6201 Posted March 25, 2023 12 hours ago, OldSchoolRC1 said: Fantastic looking buggy, the silver parts completely transform the chassis. Thanks! Share this post Link to post Share on other sites
Nicadraus 6201 Posted March 26, 2023 Update on the WO-R - Wild One-R My body reinforcement tape arrived and I applied some on the WO body. Installed the wiring and LED bulbs for the front and rear lights. I had to redo a new one. Let there be light! While it looks funny that the entire yellow housing illuminates, I actually like it. More visible at night drive. Hope the front star-dish wheels and tires arrive this week. Can't wait to do a proper photoshoot with this one. 5 Share this post Link to post Share on other sites
BuggyDad 4475 Posted March 27, 2023 3 hours ago, Nicadraus said: Wild One R Looks like it really means business. You going to splash out and go for those aluminium star dish wheels? They would rock on this thing.... Share this post Link to post Share on other sites
Nicadraus 6201 Posted March 27, 2023 23 minutes ago, BuggyDad said: Looks like it really means business. You going to splash out and go for those aluminium star dish wheels? They would rock on this thing.... If I can find those at a cheaper price, then I'd go for it. $60 for that set is kinda steep for wheels. I've spent $50 the last set of beadlock wheels for my CFX (which was the 4th set for that car) and told myself no more spending too much on wheels. Haha! Share this post Link to post Share on other sites
Nicadraus 6201 Posted March 30, 2023 Some outdoor shots. I think she even looks better in natural light. 6 Share this post Link to post Share on other sites
ploots 185 Posted March 30, 2023 Well done that man that's absolutely stunning 1 Share this post Link to post Share on other sites
Nicadraus 6201 Posted March 30, 2023 9 minutes ago, ploots said: Well done that man that's absolutely stunning Thank you mate! Share this post Link to post Share on other sites
ChrisRx718 4470 Posted April 2, 2023 Keep returning back to this thread, it looks really smart. I can't decide whether or not to splash out on the chrome-plated E-parts for my FAV. It's the Shark Mouth version so already mostly aluminium TS paint finish with green accents. Those parts look so good, just not sure if they'll look too flash on a military-esque vehicle. £24 for the bits too 1 Share this post Link to post Share on other sites
Nicadraus 6201 Posted April 4, 2023 On 4/2/2023 at 11:17 PM, ChrisRx718 said: Keep returning back to this thread, it looks really smart. I can't decide whether or not to splash out on the chrome-plated E-parts for my FAV. It's the Shark Mouth version so already mostly aluminium TS paint finish with green accents. Those parts look so good, just not sure if they'll look too flash on a military-esque vehicle. £24 for the bits too I spent about $300 on the conversion and stopped counting the cost after that. I just fooled myself pretending to be illiterate in math. But at least the result made me really happy. Since your FAV is mostly aluminum, I think the silver bits will definitely look good. Share this post Link to post Share on other sites
Nicadraus 6201 Posted June 12, 2023 I've searched for this wheel and tires combo at local shops as well as online but it was so hard-to-find. It was only in Tamiya Factory Shop in HK that I found these. Glad to have them as they look much better on the WO than the bigger ones which make the WO look like a 4WD. Comparison to the bigger ones 5 Share this post Link to post Share on other sites
Nicadraus 6201 Posted July 25, 2023 Now completed with the driver's head in detail. I should say it's "finally done". 4 Share this post Link to post Share on other sites
ChrisRx718 4470 Posted February 26 Very cool, I like your take on it. I have just finished amassing parts to build another FAV / Wild One hybrid. I'm not sure what colour scheme to go with, so I've bought both red and silver / grey rollcage parts. It will sit in a box whilst I procrastinate for another 6 months I imagine! 1 Share this post Link to post Share on other sites