Porsche 959 in excellent mint condition
DesPrinzla
Agreed, nice score. Must have cost an arm and a leg, perhaps more :-)
9-Feb-2020
Tamiya fs12-lt engine for a ta01 mre nitro conversion
Futureworks
Thanks guys :-) My start point is to get the engine sorted, then I'll strip down the chassis, clean and rebuild to include fitting radio gear so it's good to go. As for a body, that'll get left until later though it would be nice to replicate the Konig Merc in the advert above if I can find wheels and body. Current thoughts are to use the merc bodyshell I've got as part of a new built TG10-Pro 49172 I bought recently, which could fit. More (probably much) later!
11-Feb-2020
Couldn’t agree more; I think this is the nicest shell I have ever owned, and I used to have this as my TC member image until recently.
15-Feb-2020
92069 f-1 body set m type (marlboro mclaren 4/5b) f101 (now sold)
Futureworks
I remembered that Tariq has one too, so check out the comments here: https://www.tamiyaclub.com/showroom_model.asp?cid=99101&id=25685
15-Feb-2020
92069 f-1 body set m type (marlboro mclaren 4/5b) f101 (now sold)
Futureworks
And for more information in general about the 92xxx part numbers including this one, see OCD’s posting in the thread he started in the forum a few years ago about compiling a complete list of 49xxx parts: https://www.tamiyaclub.com/forum/index.php?/topic/38584-49xxx-part-numbers-complete-list/&page=2&tab=comments#comment-702379
16-Feb-2020
Retro-re-re new build
Futureworks
Thanks :-)
19-Feb-2020
Tribute at rogue element
robertoro
Amazing amount of parts and a reminder that Chris really has produced some brilliant pieces over the years. I always liked the original scorcher dash, more so that the second version. Wish he’d do another run (he did do a 2nd after all, so why not just once more). Mind you I’ve not seen anything new emerge from REC for a few years....
19-Feb-2020
Alfa romeo 155 v6 ti
Rob606
Great looking model. At first I thought it was the old TA03F (58189)from the late 1990's - hadn't realised the body had appeared again on a more modern chassis. One of my favourites with the Martini livery. Nice Job!
21-Feb-2020
Martini lotus 79
Grelberg
That really does look Great!!!!
22-Feb-2020
Dtm's: you can never go wrong with them
koenc
Nice score. Increasingly rare to see something like this listed as a NIB on TC.
22-Feb-2020
New built
Futureworks
I agree - fingers crossed it’ll happen at some point.
29-Feb-2020
Tamiya ta01 mre nitro conversion
Futureworks
Link to other showroom entry for more general info: https://www.tamiyaclub.com/showroom_model.asp?cid=134838&id=16836
Link to thread in forum about the build: https://www.tamiyaclub.com/forum/index.php?/topic/92380-repairing-a-fs12-lt-engine-mre-ta01-nitro-conversion-build-thread/
3-Mar-2020
Acoms ap-202 nib x 2 (now sold)
Futureworks
Great article setting out the history and evolution of the Acoms radio sets can be found here: https://tamiyabase.com/forum/11-technical/3503-acoms-2-channel-stick-radio-evolution
14-Mar-2020
A monster
DesPrinzla
Amazing condition! Did you also get the upgrade parts to address the gearbox design problem on this model which was sorted out on the release of the Jugg II..?
16-Mar-2020
New built & fully hopped-up
Futureworks
Couldn’t agree more :-)
17-Mar-2020
Thunder tiger ta02 nitro conversion - new built (sold)
Futureworks
Thanks, you’re right, a very lucky find and in pristine condition :-)
18-Mar-2020
Tamiya ta01 mre nitro conversion
Futureworks
So an update on the muffler issue - acprc identified that I was missing a spacer which would have come with the original conversion kit. Being a loose item, this part was not included with the new built chassis I purchased as it had probably been lost by the original owner. Luckily acprc didn't use the spacer for his MRE build, and I now have it - as pictured (all held in place with matchsticks pending arrival of some very long M3 bolts). That's a major problem now resolved, so I can get on with stripping down the chassis to clean and check all parts before the build.
18-Mar-2020
Tamiya ta01 mre nitro conversion
Futureworks
M3 x 55mm is what's needed, and hopefully arriving in the post shortly!
20-Mar-2020
Nib
Futureworks
Great article about this model in another TC showroom here: https://www.tamiyaclub.com/showroom_model.asp?cid=125893&id=125893
21-Mar-2020
Kyosho 1/8 hor bike
ruscandr
Beautiful job! Other than body and rider, looks like you’ve replaced almost all the original Kyosho parts. Would be great to have a complete list of all of the parts, some of which (like the carbon chassis) I’ve not seen before.
22-Mar-2020